Touch issue repair in Gurgaon.
An iPad screen that ignores touch, jumps or taps by itself, traced to the glass, the display or the board.
- Starting price
- ₹3,499 onwards
- Typical time
- 45 min
- Warranty
- Up to 6 months
- Where
- At your doorstep
- Expert engineers
- ·
- Up to 6-month warranty
- ·
- Doorstep in Gurgaon
Touch issue price in Gurgaon, device by device.
Starting price for each device we currently carry parts for, across 1 models. Each figure is the lowest quoted parts grade for that model; the engineer confirms the exact price in writing after the on-site diagnosis, before any work starts.
Apple · iPad 5th Gen
| Device | From | Turnaround |
|---|---|---|
| iPad 5th Gen (9.7 inch) | ₹3,499 | 45 min |
If any of this sounds familiar, you are in the right place.
What you get
- Free 21-point pre-repair diagnosis. You see the report before any quote.
- Fixed price quoted in writing. No surprise add-ons, no diagnostic fee if we don't fix it.
- Repair performed by an expert engineer at your home or office in Gurgaon.
- New water-resistance seals fitted whenever a sealed phone is opened.
- Up to 6-month parts and workmanship warranty, transferable to a new owner.
What a touch issue repair involves
A touch issue repair fixes a screen that shows a picture but does not respond properly. On phones the touch layer is laminated into the display, so a failed touch layer usually means a screen replacement. On iPads with a separate front glass, like the 9.7-inch 5th-generation iPad this page currently prices, the touch glass can be replaced without the display underneath.
What the symptoms mean
- A strip or patch that never responds
- The touch layer is damaged in that area, often along a crack.
- The screen taps by itself
- Ghost touch comes from a damaged touch layer, a poor earlier replacement, or a noisy charger. Unplug it and see whether it stops.
- Touch fails only after warming up or while charging
- A battery swelling against the panel, which presses harder as it warms, or electrical noise from the charger.
- A grey flickering bar and touch dropping out on an older iPhone
- On the iPhone 6 Plus especially, this is a touch chip fault on the board, not the screen.
How the job is done
- 01The diagnosis runs with the case, protector and charger removed, drawing lines edge to edge across the screen so any dead zone shows as a gap.
- 02The engineer decides which layer has failed: a separate touch glass, the full display assembly, or the touch circuit on the board.
- 03On an iPad with a separate glass, the old glass is released from its adhesive and the home button is moved onto the new glass so Touch ID keeps working.
- 04The new glass is bonded and left to set flat. The engineer tells you at diagnosis whether that happens at your table or at the Sector 49 bench, along with any touch chip work on the board.
- 05Multi-touch gestures, typing near the edges and Touch ID are tested before handover.
What decides the price
Which layer has failed decides the price. A separate touch glass on an older iPad is a smaller part than a full display assembly, while a touch chip on the board is bench work priced after inspection. On phones the touch layer and the display are one part, so the screen grades apply. If the LCD under an iPad's touch glass is cracked too, both are needed, and that is checked before the quote.
Before and after
- Try a different charger and test unplugged before booking; a faulty charger can make touch behave erratically.
- Remove the screen protector first, because a lifted edge mimics a dead zone.
- On an iPad with Touch ID, tell the engineer if the home button has ever been replaced, because only the original keeps fingerprint unlock.
More about touch issue repair
Answered in full on their own pages
Book your repair now. We'll be there by evening.
Two minutes to book. A fixed quote in your inbox. An engineer at your door, with the parts already in the kit.